Re: Space Hulk Doors Closed and Open Heroquest style

Posted by Captin Kabeered on May 11, 2013; 6:05pm
URL: http://the-lost-and-the-damned.71.s1.nabble.com/Space-Hulk-Doors-Closed-and-Open-Heroquest-style-tp7578580p7579927.html

Hi Sirenix,

Sorry to hear about your Hard Drive brake down. It must be a knightmare...
In Regards to your edit 1 points about The SH3 Doors would this help?

http://www.mediafire.com/view/?p4duadkh7g5sxer

I have placed the items on my mediafire page.

Here are some Idears I have had for SC door ways. I remebered that when I 1st got SC the doors were dire cut attched to the Cross sections The door frames that attach to the board joiners. (The black plasic clips in the shape of a cross for the top and a T for keeping the sides in place.)

SC door frame with gap along the fold.
Door_Frames_6.png
http://www.mediafire.com/view/?idi96kdf8i4bgk9
SC door frame attched at the top.
Door_Frames_7.png
http://www.mediafire.com/view/?umcq1c7w3427zgw
SC door frame attched at the bottem.
Door_Frames_3.png
http://www.mediafire.com/view/?fvvmvy542a4x4f3
SC floor frame bases - 2 per door frame one each side of the door hole.
Door_Frames_9.png
http://www.mediafire.com/view/?qs2348hgpcjdqvh

MD door frame attached with gap along the fold.
Dreadnought_Door_Frames_3.png
http://www.mediafire.com/view/?c6ygwiw8sg2bybl
MD door frames attached allong the top with bilt in fold overstand tabs.
Dreadnought_Door_Frames_4.png
http://www.mediafire.com/view/?o30f3kltfpp56bw

Instructions to attach and make door frames:-

Step  1. Print Door_Frames_6.png,
Step  2. Fold down the middle,
Step  3. Cut out the door way section (leaving the white bits under the frame to act as a stand) or ( to use as attachment),
Step  4. Print and cut out Door_Frames_9.png,
Step  5. Attach one to each side of the door frame. The door frame will know be standing on the 'Frame Bases',
Step  6. Place on game board each side of the gray door space,

        -Optional 6a. Use the frame bases as an alternative to the existing door spaces on the boards.

Step  7. Cut two strips of paper and attach one each side of the door frame (The strips need to be a bit longer than the door frame.),
Step  8. Fold over the strip tabs and attach each one to a different 'Frame Bases'.

        - Optional 8a To give them more strength the door frames and frame bases can be attached to thin card.
 
The frame bases can be placed on the board with the door frames standing upright on top.

Step  9. Print and fold Door_Frames_7.png back to back so the frame is visable,
Step 10. Cut out the door section,
Step 11. Use some of the cut paper as strip tabs and attach to the 'Frame Bases'(See Steps 7 and 8.),
Step 12. Print out Dreadnought_Door_Frames_3.png fold along the white section and attach to the 'Frame Bases'.

Step 13. Print out Dreadnought_Door_Frames_4.png Fold along the middle left to right,
Step 14. Cut out the door space keeping the white space of the frame as tabs,
Step 15. Fold over the remaning white tabs and attach to the opposite sides white tab.


Here is a post with a link to the SC door frames
http://the-lost-and-the-damned.664610.n2.nabble.com/Space-Crusade-rule-book-expansions-and-board-downloads-td4044772.html

and Dreadnought door frames
http://the-lost-and-the-damned.664610.n2.nabble.com/Space-Crusade-PDFs-Eldar-Attack-and-Mission-Dreadnought-and-others-td5800312.html

I hope that gives you some help and idears.

Good luck..
P.s. I like seeing the door harlf open i.e. not fully open as it add to the run down space ship is going to need to find a dry dock soon feel.
P.S.2: Althogh it might be difficult for line of site and manoovering through the door gaps. It would be good to have a full set of your partly open doors.

It is good too mix and match the original doors and your extra and new doors, amongst others. Having some fully open, parshally open, and closed.

Keep up the good work